Process: hardening and tempering – Dimension range: diameters up to 120 mm width up to 65 mm – Cycle time: 15 seconds – Power: 350 kW – Handling: conveyors – Additional features: Dimensional control systems before treatment, Set-up for type change in a few minutes, Recipes with parameterized programming, Control parameters system
 

Process: hardening and tempering of inner rings and outer rings – Dimension range: diameters from 80 mm to 330 mm width from 50 mm to 200 mm, max weight 20Kg – Cycle time: 30 seconds – Power: 1000 kW – Handling: automatic with conveyors – Additional features: Dimensional control systems before treatment, Laser marking, Washing station, Control parameters system
 

Process: hardening and tempering of inner rings and outer rings – Dimension range: diameters from 110 mm to 320 mm width from 40 mm to 200 mm, max weight 40 kg – Cycle time: 60 seconds – Power: 2150 kW – Handling: automatic with robot – Additional features: Dimensional control systems before treatment, Laser marking, Washing station, Control parameters system
 

Process: spray coating – Dimension range: diameters up to 60 mm – Cycle time: 6 seconds – Power: 25 kW – Handling: conveyors – Additional features: Dimensional control systems before treatment, Set-up for type change in a few minutes, Recipes with parameterized programming, Control parameters system
 

Process: shrink fitting of stator – Dimension range: asynchronous motor housing sizes Gr. 63, 71 and 80 – Cycle time: 20 seconds – Power: 50 kW – Handling: automatic with conveyor and rotating table – Additional features: Control parameters system
 

Process: shrink fitting of shaft in rotor for traction motors – Dimension range: diameters
range 25 mm - 75 mm – Cycle time: 120 seconds – Power: 175 kW – Handling: automatic
with linear transfer– Additional features: Control parameters system, Dimensional control
systems before treatment, Recipes with parameterized programming

Process: shrink fitting of stator in housing for traction motors – Dimension range:
diameters range 175 mm - 280 mm, height range 130 – 240 mm – Cycle time: 120 seconds –
Power: 100 kW – Handling: automatic with linear transfer– Additional features: Control
parameters system, Dimensional control systems before treatment, Recipes with
parameterized programming
 

Process: Hardening and Tempering– Dimension range: tailstocks max lenght 2000 mm and
max oD 600 mm, on spindle max oD 1000 mm, on working table max 2000 x 900 mm –
Frequency: 20 – 300 kHz– Power: 150 kW – Axis: 1 vertical Z, 1 horizontal Y, 1 horizontal X, 2
rotating A and B – Handling: manual – Additional features: Control parameters system,
Recipes with parameterized programming, vertical scanning, horizontal scanning, single
shot, teleservice
 

Process: Hardening and Tempering– Dimension range: max lenght 1200 mm on tailstocks,
max oD 350 mm – Frequency: 6-20 kHz– Power: 300 kW – Axis: 2 vertical Z, 2 horizontal Y, 2
horizontal X, 1 rotating A – Handling: automatic with robot and camera– Additional
features: Control parameters system, Recipes with parameterized programming, vertical
scanning, horizontal scanning, single shot, frequency and heating station switching system ,
workpiece position control with laser, teleservice
 

Process: Hardening and Tempering– Dimension range: max lenght 2000 mm on tailstocks,
max oD 800 mm, working table max 2500 mm – Frequency: 4 – 300 kHz – Power: 650 kW
(400 kW + 150 kW + 100 kW) – Axis: 2 vertical Z, 2 horizontal Y, 1 horizontal X, 2 rests, 1
tailstock with a magnetic V-block, 1 rotating A – Handling: manual – Additional features:
Control parameters system, Recipes with parameterized programming, vertical scanning,
horizontal scanning, single shot, generators automatic switch, teleservice